Jan 12, 2026

How to test a motorised globe valve?

Leave a message

Hey there! As a motorised globe valve supplier, I often get asked about how to test these valves. Testing a motorised globe valve is crucial to ensure it functions properly and meets the required standards. In this blog, I'll walk you through the step - by - step process of testing a motorised globe valve.

1. Pre - test Inspection

Before you start the actual testing, it's essential to do a pre - test inspection. First, visually check the valve for any physical damage. Look for cracks in the valve body, bent stems, or any signs of corrosion. A damaged valve might not work correctly, and it's better to identify these issues early on.

Next, check the electrical connections. Make sure all the wires are properly connected and there are no loose ends. Loose electrical connections can lead to malfunctions during the testing process. Also, verify that the power supply to the motorised part of the valve is correct. The voltage and frequency should match the valve's specifications.

2. Functionality Testing

Opening and Closing

The most basic test is to check if the valve can open and close properly. Use the control system to send commands to the motor to open the valve. Observe the movement of the valve stem. It should move smoothly without any jerks or sticking. If the stem gets stuck, it could be due to debris inside the valve or a problem with the motor.

Once the valve is fully open, send a command to close it. Again, watch the stem movement. The valve should close completely, and there should be no leakage when it's in the closed position. To check for leakage, you can use a pressure gauge on both sides of the valve. If there's a pressure difference when the valve is closed, it indicates a leak.

Position Feedback

Most motorised globe valves come with a position feedback system. This system tells you the exact position of the valve (open, closed, or somewhere in between). Test this feature by sending commands to the valve and checking if the position feedback on the control panel matches the actual position of the valve. If there's a discrepancy, there might be an issue with the position sensor.

3. Flow Testing

Flow testing is important to ensure that the valve can regulate the flow of fluid as intended. You'll need a flow meter for this test. First, set the valve to a specific opening position, say 50%. Then, measure the flow rate of the fluid passing through the valve using the flow meter.

Compare the measured flow rate with the expected flow rate based on the valve's specifications. If the measured flow rate is significantly different, it could mean that the valve is not regulating the flow correctly. You can repeat this test at different opening positions to get a comprehensive understanding of the valve's flow - regulating capabilities.

4. Pressure Testing

Pressure testing helps to determine if the valve can withstand the required pressure without leaking or getting damaged. Connect a pressure source to the inlet side of the valve. Gradually increase the pressure to the maximum rated pressure of the valve.

Keep an eye on the valve for any signs of leakage, such as drops of fluid around the valve body or stem. Also, check if the valve can maintain its position under pressure. If the valve starts to open or close unexpectedly under pressure, it's a sign of a problem.

3B25B  3 Way Ball Valve (3)Plastic 2-way ball valve2

5. Motor Performance Testing

The motor is the heart of a motorised globe valve. To test the motor performance, you can measure its electrical parameters. Use a multimeter to measure the current and voltage drawn by the motor during operation. Compare these values with the motor's rated values.

If the current is too high, it could indicate a problem with the motor, such as a short - circuit or excessive load. On the other hand, if the current is too low, the motor might not be getting enough power. You can also listen to the motor while it's running. A noisy motor could be a sign of worn - out bearings or other mechanical issues.

6. Compatibility Testing

If the motorised globe valve is part of a larger system, it's important to test its compatibility with other components. For example, if it's connected to a control system, make sure that the valve can receive and execute commands from the control system without any issues.

Also, test the valve's compatibility with the fluid it will be handling. Some fluids can be corrosive or abrasive, which can damage the valve over time. Check if the valve's materials are suitable for the specific fluid.

Related Products

If you're interested in other types of valves, we also offer some great products. For instance, our Electric Actuator 3 Way Ball Valve is a versatile option for many applications. It can handle different flow directions and is known for its reliable performance.

Another product is the Quick Response Shut Off Electric Valve. This valve is designed to close quickly in case of an emergency, providing an extra layer of safety. And don't forget our 2 Electric Ball Valve, which is a simple yet effective solution for controlling the flow of fluids.

Conclusion

Testing a motorised globe valve is a comprehensive process that involves multiple steps. By following these steps, you can ensure that the valve is in good working condition and meets your requirements. If you have any questions about testing or if you're interested in purchasing our motorised globe valves, feel free to reach out. We're always here to help you with your valve needs and can discuss the best options for your specific application. Let's get in touch and start a great business relationship!

References

  • Valve Handbook, 4th Edition by Robert W. McKetta
  • Fluid Mechanics and Thermodynamics of Turbomachinery by S. L. Dixon
Send Inquiry